0
Owner's of the Cuisinart Blender SMARTPOWER DELUXE gave it a score of 0 out of 5. Here's how the scores stacked up:
6
Ice Crush can also be used in Pulse mode. See
Recipe Tips section on page 2 of the recipe booklet
for more details.
9. To dislodge food: Use a rubber or plastic spatula
to help remove food lodged around the cutting
assembly. Do not use spatula until you have turned
the blender off. Replace the cover and measured
pour lid and continue blending, if necessary.
Make sure spatula is not inside the blender jar
before blending.
10.
When finished blending: Press the On/Off button
and unplug the blender from the electrical outlet.
Never remove the blender jar from the motor base
until the blender is off. Do not twist locking ring from
blender jar when removing jar from motor base.
Simply lift blender jar from motor base. Do not put
hands into blender jar with blender plugged in.
CLEANING AND MAINTENANCE
Always unplug your Cuisinart
®
SmartPower
®
Deluxe
™
600-Watt Blender from the electrical outlet before
cleaning. The blender is made of corrosion-resistant
parts that are easy to clean. Before first use and after
every use, clean each part thoroughly. Periodically
check all parts before reassembly. If any part is
damaged or blender jar is chipped or cracked, DO
NOT USE BLENDER.
Remove the blender jar from the motor base by lifting
straight up and away. Twist off the locking ring by
turning counterclockwise.
Remove the cutting assembly and rubber gasket.
Wash in warm soapy water, rinse, and dry thoroughly.
Place the locking ring in the upper rack of the
dishwasher or wash in warm water.
CAUTION: Handle the cutting assembly carefully. It is
SHARP and may cause injury. Do not attempt to remove
blades from cutting assembly.
Remove the blender jar cover and the measured
pour lid. Wash in warm, soapy water; rinse and dry
thoroughly, or place in upper rack of dishwasher. The
blender jar must be washed in warm, soapy water and
rinsed and dried thoroughly. The blender jar can also
be placed upside down in dishwasher.
Finally, wipe the motor base clean with a damp cloth
to remove any residue, and dry thoroughly. Never
submerge the motor base in water or other liquid, or
place in a dishwasher.
Tip: You may wish to clean your blender cutting
assembly as follows: Squirt a small amount of
dishwashing liquid into assembled blender jar and fill
halfway with warm water. Run on Low for 15 seconds.
Repeat, using clean tap water. Empty blender jar and
carefully disassemble parts. Wash cutting assembly,
gasket and locking ring in warm, soapy water. Rinse
and dry all parts thoroughly.
DOs and DON’Ts
WHEN USING YOUR BLENDER
DO:
• Make sure the electrical outlet is rated at the same
voltage as that stated on the bottom of the blender
motor base.
• Always use the blender on a clean, sturdy and dry
surface.
• Always add liquid ingredients to the blender jar
first, then add remaining ingredients. This will
ensure that ingredients are uniformly mixed.
• Cut most foods into cubes approximately ½ inch
(1.3 cm) to 1 inch (2.5 cm) to achieve a more
uniform result. Cut all cheeses into pieces no
larger than ½ inch (1.3 cm).
• Use the measured pour lid to measure liquid
ingredients such as alcohol. Replace measured
pour lid after ingredients have been added.
• Use a rubber or plastic spatula as needed, only
when the blender is turned off. Never use metal
utensils, as damage may occur to the blender jar
or cutting assembly.
• Place cover on firmly. Always operate the blender
with the cover on.
• Make sure locking ring is tightly attached to
blender jar.
• Always remove locking ring, cutting assembly, and
rubber gasket before cleaning.
• When scraping the blender jar with a spatula,
remove the food from the sides of the blender jar
and place food in the center of the blender jar,
over the cutting assembly.
• When chopping fresh herbs, garlic, onion, zest,
bread crumbs, nuts, spices, etc., make sure the
blender jar and cutting assembly are completely
dry.
• If food tends to stick to the sides of the blender jar
when blending, pulse in short bursts.
• Pulses should be short bursts. Space the pulses
so the blades stop rotating between pulses.
D
•
•
•
•
•
•
•
•
•
•
•
•
Find Your Products By Category
Please Login
