Keurig Coffeemaker Cuisinart Keurig Single-Cup BrewerCuisinart Keurig Single-Cup Brewer User Manual

4.7

Out of 4 Ratings

Owner's of the Keurig Coffeemaker Cuisinart Keurig Single-Cup BrewerCuisinart Keurig Single-Cup Brewer gave it a score of 4.7 out of 5. Here's how the scores stacked up:

  • Reliability

    4.75 out of 5

  • Durability

    4.5 out of 5

  • Maintenance

    4.75 out of 5

  • Performance

    5.0 out of 5

  • Ease of Use

    4.5 out of 5
of 25
 
21
Troubleshooting
Problem: Solution:
Brewer does not have
power.
Plug Brewer into an independent outlet.
Make sure the Brewer is securely plugged in.
Plug into a different outlet.
Reset your home’s circuit breaker.
Confirm the power has been turned on and the LCD is illuminated.
Brewer will not brew. Every once in a while an air bubble may get trapped in the water path. Lift off the
reservoir, then put it back into place.
Turn off and unplug the brewer for 30 seconds or more. When you plug the brewer
back in, be sure to turn the power back on.
Make sure the water reservoir is properly in place, and perform a Rinse cycle.
After placing the K-Cup® in the K-Cup® Holder, make sure the handle is pushed
down securely and the LCD control panel reads READY. The
and buttons,
Brew, Hot Water, and Rinse buttons will be illuminated. Then press any of the lit
buttons.
If the LCD control panel indicates ADD WATER, check to make sure the water
reservoir is properly filled. If not, add water. If so, make sure the water reservoir is
properly seated in its base.
If the LCD control panel indicates ADD WATER even after refilling and checking the
base, contact Customer Service at 1-800-726-0190.
The exit needle may be clogged (refer to page 19).
Chlorine or mineral
taste in coffee.
Consider using bottled water, filtered water or the Cuisinart Charcoal Water Filter.
Doesn’t brew a full cup. Every once in a while an air bubble may get trapped in the water path. Lift off the
reservoir, then put it back into place.
Turn off and unplug the brewer for 30 seconds or more. When you plug the brewer
back in, be sure to turn the power back on.
The exit needle may be clogged (refer to “Cleaning & Maintenance” page 18).
Clean the K-Cup® holder brewing chamber (refer to “Cleaning & Maintenance”
page 18).
Make sure the water reservoir is properly in place, and perform a Rinse cycle.
De-scale the Brewer (refer to page 20).
If you have repeated the de-scale procedure two times and it is still only brewing a
partial cup, contact Customer Service at 1-800-726-0190.
The time is not
displayed on the LCD
control panel.
You must set the clock (refer to page 15) in order for the time to be displayed on
the LCD.
If power is interrupted to the Brewer, you will need to re-set the clock (refer to
page 15).
Brewer shuts off, or
turns on, automatically.
Make sure the Auto Off and the On/Off time features have not been set. To do this,
press the Menu button and scroll through the programming options. OFF should be
displayed for Auto Off timer and On/Off. If OFF is not displayed, you must reset
(refer to page 15).
The blue light in the
water reservoir is
flashing.
This indicates the water level in the reservoir is low and water must be added (refer
to page 14) in order to brew a full cup.
Coffee is too weak or
watery.
Reduce the brew size for a stronger-tasting cup of coffee (refer to “Programming
Your Brew Size” on page 18). Try an Extra Bold K-Cup®. It has 30% more ground
coffee in each portion pack.

   Find Your Products By Category